Behringer Europower-p0569 Hca2400 Sps1000 Dpx Pmp-1280s 5000 Sch - Download as PDF File (.pdf), Text File (.txt) or view presentation slides online. This tool Behringer Europower Pmx2000 Owners Manual your. Under Utilities, we could access the programs. Download App. Still, this program is fabulous, free.

'The EQ side'??? Not sure what you mean. Behringer holds their documatation very tightly, service centers have to sign a non-disclosure agreement. There are a few schematics floating around for some models. If you can be more specific, I may be able to help.Thanks Enzo, I have talked back with my friend and it's not the EQ (equalizer) but all the effect section on the right which is not working, and no leds come on. May be a bad supply output, don't know if each section have a separate supply output. I didn't open it, even see it yet.

C:\program Files (x86)\counter-strike 1.6 \hl.exe Game Cstrike. I'll go there this weekend to take a look. I went today to my friend's church to see the problem with the mixer.

Indeed, all the effects section was dead, no LEDs on neither the two numeric displays. I opened the box (was not evident at the first look which screws I had to remove to open it.:-) ) and go directly to the supply board. Then I saw there were 3 fuses on the board. I probed them all, and F1 was blown, I replaced it and all the system came back to life. It seems to be ok, not sure how it will behave in the long run. Was it only a bad fuse or there is something beggining to drain more current.

Time will say. Thanks Enzo and Jazz for your replies, I appreciate it. Dead shorts in low current portions of these are more times than not, shorted chip bypass capacitors.

They are mounted near the rails of every IC on the efx board. There are lots of possible tracing tricks, but I doubt is you have the equipment needed to isolate one of dozens of bypass caps on the same 5volt rail. A milliohm meter would be useful, particularly if it has '4-wire' measurement capability. I use a pulse generator driving from 0 to peak 5 volts and look for ringing on a scope or using a current loop. Another method would be running the module directly from a current limiting bench power supply and isolate which rail traces have the greatest voltage drop. Another way that is not recommended for all situations but using a high current regulated power supply, and adjustable current limiting set to about 10 amps. Using large gauge wire, connect the ground well on the module and briefly touch the supply positive lead to the +5volt rail on the module.

The shorted cap will burn itself out clearing the short. Replace the cap with another surface mount bypass and reassemble the unit. When I had my large service shop, with 15 techs working on dozens of Behringers a day, handling the entire western half of the US(Behringer only had two shops do all their work at that time), we probably had to find 5,000-6000 shorted surface mount bypasses. Maybe one of the op amps. Do you have a schematic? I have the pmp5000 service manual.I accidentally plugged the outputs of an external power amp to the monitor 1 & 2 sends on my PMP5000 and powered it up. After realizing what I had just done, I corrected my connections, powered up, and now my monitor sends and dead, and my effects section is also dead.

Everything works, including the internal power amp. I you send me a copy of the manual, or help my with a diag?? I did not want to open without a manual. Thank You very much with any help you may be able to supply! Zuma Revenge Full Version Torent Kickass. ! Here is the schematic of the PMP 5000: Scroll down to the little link 'get manual' and click to download. IGNORE other download links. You are going to find the following during repair: Most likely a failure in the HCA2400 amp module has fried the power supply and you will have to repair/replace the HCA2400 before powering up with a repaired SPS1000 or you will get to do it all over again.

The HCA2400 rear chaannel has a habit of arcing between layers of the multi-layer circuit board in the vicinity of the source lead of one of the SFP9640 transistors. I usually have to grind away this area to get rid of the 'cancer' and reinsulate and replace the traces with jumpers.

I have photos of most of this work. The usual thing is the three switching transistors are shorted OR degraded and all have to be replaced for reliability. Often one of the 18 volt Zener gate voltage limiting diodes is fried as well. In some cases the.03 ohm metering resistor on the bottom is fried and board restoration PLUS two small SMT transistors that are part of the current limiter in the HCA2400 will be blown IF that resistor has smoked.